Show
The Allison Transmission Speed Sensor changed in mid 2015. If you own a 2015, use the diagram in the image gallery above to match the connector to the correct sensor. A failing speed senor on your Allison transmission can give erratic readings causing shifting concerns, dtc codes, and other issues. Reviews & Questions What Does an Allison 3000 Series Transmission Look Like?Curious about your medium-duty vehicle’s transmission? You’ve come to the right place. Today, Catalyst Powertrain Service Manager Craig Oster is providing a closer look at the Allison 3000 Series Transmission. Why We Chose the Allison 3000The Allison 3000 Transmission is the most-used transmission on the road today for trucks. In our last episode, Shop Talk: Check Transmission Light, we used an Allison 3000 Transmission as our example – not because it’s a problematic transmission, quite the opposite – because it is the workhorse transmission for medium-duty trucks most in use today. The Allison 3000 has been in production since 1993. Medium-duty Class 6 trucks using the 3000 transmissions have an average age of 2.12 (the oldest on the road) and there are an estimated 2.155 million of these active trucks in service. What is Considered a Medium-Duty Truck?Freightliner.com has written extensively about medium-duty trucks. Medium-duty trucks fall into Classes 6-7 and have a gross vehicle weight (GVW) rating range of 19,501- 60,000 lbs. Medium duty trucks are used for a variety of lighter duty applications. Allison 3000 Series Transmission AnatomyOrientationIn this illustration, the right is the driver’s side and the left is the passenger side. The large end of the transmission faces the front of the vehicle. Allison 3000 Series Torque ConverterThe torque converter is located at the front of the Allison 3000 Series transmission in the center of the dial as highlighted in Figure 2 (above). Of course, with the transmission installed and functioning, there is no way to “see” the torque converter, but this is where it located. Purpose of the Torque ConverterThe transmission torque converter is a fluid coupling that enables the vehicle to get started. Then, as the speeds progress, it has a lockup clutch within the torque converter that applies to make it to make a 1-to-many connection. Engine Speed SensorPurpose of the Engine Speed SensorThe Engine Speed Sensor assessed the speed at which the crankshaft spins. This electronic control device sends crucial information to the transmission. The PTOThe PTO can be driven off of either side of the transmission. Therefore, there are two plates on either side as shown below: Dipstick HoleAllison 3000 Series transmissions are manufactured with a dipstick hole on either side of the transmission. One side or the other will be in use; the side not in use will be plugged (see Figure 11 below). Allison 3000 Series Transmission Data TagThe transmission data tag displays information such as the serial number and sometimes the part number, but most importantly, it displays how the transmission was built. This tells mechanics everything they need to know about how a transmission is built. This is located below the Dipstick Hole on the transmission (see Figure 13 below): Main Transmission Connector or 20-Way ConnectorThe 20-Way connector is located beside and behind the dipstick hole as shown in Figure 14 (below). It is considered the transmission’s artery, running from the computer to the transmission’s main solenoids, transmission, and to the switches. Dipstick Tube Mounting HoleThe bolt hole directly above the 20-way connector is the mounting hole to the dipstick tube (see Figure 15 below). Allison 3000 Series Transmission Output Speed SensorThe output speed sensor is located at the lower rear of the transmission, behind the 20-way connector (see Figure 17 below). In our previous discussion, Shop Talk: Check Transmission Light, we recommended checking the Output Speed Sensor. The Allison 3000 Series transmission’s Turbin Speed Sensor is located inside the transmission. Note: The Allison 1000 Series, 2000 Series, and 4000 Series transmissions have three external speed sensors:
Allison 3000 Series Transmission Control Module (Underside of Transmission)Two Filter Areas on Either Side of the TransmissionThere is a Main Filter (Figure 18: Right Side) and a Lube Filter (Figure 18: Left Side). The filters come in a kit that contains the filters, seals, and gaskets. Allison 3000 Series Transmission Oil FlowOil leaves the transmission to be cooled (see Figure 19 below) via the To Cooler Port and returns to the transmission (see Figure 20 below) via the From Cooler Port. Notice the Arrow pointing up to a plug labeled “To Cooler.” The To Cooler Port is where the oil leaves the transmission and goes to an oil cooler to be cooled. In Figure 20 below, notice the incoming arrow pointing down towards the Lube filter. This is the From Cooler Port is where the cooled oil returns to the transmission. Allison 3000 Series Transmission ClutchesThe Allison 3000 Transmissions allows for the capability to check individual clutch pressures. We can diagnose each individual clutch. In Figure 21 (below), notice the individual clutch numbers. Those, predictably, correspond to that specific clutch. So these are the main components of the Allison 3000 Series Transmission. We hope this tour has been helpful to those who want to better understand the location of the main components of this transmission. Where is the speed sensor located on a 4L60E transmission?The transmission connector is located on the passenger side of the 4L60E transmission housing and on the driver side of the 4L80E transmission housing. The vehicle speed sensor is located in the tail shaft housing on the passenger side.
What happens when speed sensor goes out?When there's no speed signal coming from the sensors, shifting of gears will be a problem because the powertrain control module won't control them correctly. This will make the transmission not work properly. It will either shift more quickly or roughly than expected.
Are input and output speed sensors the same part?Typically, two sensors communicate the transmission data to the vehicle's powertrain control module. The first sensor, referred to as the input sensor, monitors the speed of the transmission's input shaft. The second sensor is the output sensor, which monitors the output shaft speed.
|
Allison 1000 output speed sensor location
Related Posts
Copyright © 2024 nguoilontuoi Inc.
