Joined Jun 11, 2009 · 86 Posts
Discussion Starter · #1 ·
Jun 20, 2012 Does anybody have a write up or pictures of how to replace the waterpump on an 03 WJ 4.0L? Whats everybody using for replacement brand? Joined Jan 22, 2011 · 10,676 Posts
I used MasterPro Select from O'reilly Auto. It's quite a simple procedure. Basically, you take off the belt, unbolt the 4 bolts holding the pulley on, pop the pulley off, remove the hoses that are clamped onto the water pump, then remove the bolts holding the water pump on. Clean it up and slap the new one on (with a gasket of course). When
you clean it, be sure both surfaces are free of any old gasket. Also, you may want to stuff a shop towel or two into the hole in the head to avoid getting old gasket material in there while you clean it. On reassembly, I think I went above and beyond and also used a little RTV along with the new gasket to ensure I would have no leaks. You will need to transfer the old pulley and the metal tube from the old pump to the new pump as well. At this point, I would consider a new thermostat and
flushing the cooling system and refilling with a 50/50 mixture of Zerex G-05/Water. Here's a picture of the water pump. The thermostat is right above the water pump.
Joined Aug 23, 2011 · 147 Posts
Make sure you put the 90 degree tube on the new water pump BEFORE you install it onto the engine. It won't go on after you've installed the water pump, there isn't any room to twist it on, the valve cover is in the way. I learned this the hard way.
Joined Jan 22, 2011
·
10,676 Posts
Joined Jun 15, 2010
·
1,582 Posts
Make sure you put the 90 degree tube on the new water pump BEFORE you install it onto the engine. It won't go on after you've installed the water pump, there isn't any room to twist it on, the valve cover is in the way. I learned this the hard way. great advice thanks a lot!! i have to track down a coolant
leak this weekend.
Joined Sep 17, 2011
·
371 Posts
I've used GMB water pump's from Advance Auto Parts on both WJ's and been happy so far. Plus if you order online using Promotion: CCABIN Good luck...
$10 off orders of $30 or more - $20 off orders of $50 or more - $40 off orders of $100 or more!! Just order online, get the discount and designate to pick up the parts at your neighborhood store. So your ~$57 WP
is ~$37.
Joined Jun 1, 2012
·
3 Posts
this help me out too!. Thanks ChrisHager!
Joined Jul 22, 2011
·
46 Posts
Be sure not to overtighten the thermostat housing/ or water pump bolts. I felt like a complete tool when i did that.
Joined Jun 30, 2010
·
180 Posts
It sounds simple on paper or computer screen. Mine was fun. It took about 3 or so hours. Then again I have the tow package so I have two fans plus trans cooler. Just from my experience go a head and replace the radiator and hoses. I skimped on the radiator and was pulling it about two weeks later. If its worth doing once its worth
doing right!!!
Joined Sep 19, 2008
·
1,032 Posts
its easier than you think, i did mine with the fan out (was also replacing it) so it made it easier, and i also used the GMB new (not reman) water pump from advance, only advice ill give you is DO NOT just use the gasket, put some rtv (they will give you the right stuff) on the pump where the gasket goes, then put the gasket on then put more sealant on top
of the gasket, and like everyone else said, put the metal pipe on before you install the new pump (personally i just got a new pipe from the dealer, was about $20) and the bolt torque is 22 ft lbs on the bolts for the pump, id suggest while your in there getting a new t-stat, its an easy 2 bolts, and only use mopar coolant, should be there 5year/100k coolant
Joined Jan 22, 2011
·
10,676 Posts
kc2mrg said: ...and only use mopar coolant, should be there 5year/100k coolant Zerex G-05 fits Mopar's standards...
Joined Sep 19, 2008
·
1,032 Posts
Zerex G-05 fits Mopar's standards... hmm... didnt know that, thanks for the info, it was just easier for me to buzz down to the jeep dealer down the road and get there stuff, just what ever you do, do not mix different color coolants!
Joined Jan 22, 2011
·
10,676 Posts
Believe it or not I've *heard* color doesn't necessarily designate what blend you have. But yes, a good rule of thumb is: Never mix colors. Safest bet.
Joined Jan 16, 2012
·
13 Posts
What metal pipe are you guys talking about to Install before installing the pump
Joined Jun 8, 2011
·
2,210 Posts
The heater core feed tube on the left side, see the picture above. Also, I started buying water pumps labeled as "New" not reman after a batch of bad water pumps from autozone years ago on my chevy 350.
Joined Jul 19, 2013
·
77 Posts
I put the 90 degree tube on a tried to get the pump on but I had to loosen that tube a 3/4 of a turn and then tightin it a half turn... will this cause a leak? And also how can I get the belt back on I took the pulley off to the left but now its tight getting on. I am working on a 4.0L 98 jeep grand cherokee
Joined Aug 29, 2012
·
776 Posts
The Advance water pump has a metal impeller which is GOOD. Most others and OEM are plastic. My OEM plastic impeller broke just this week.
Joined Jan 19, 2012
·
1,260 Posts
I put the 90 degree tube on a tried to get the pump on but I had to loosen that tube a 3/4 of a turn and then tightin it a half turn... will this cause a leak? And also how can I get the belt back on I took the pulley off to the left but now its tight getting on. I am working on a 4.0L 98 jeep grand cherokee On your 98 ZJ 4.0 you wrench the bolt that goes through the pulley (belt tensioner) clockwise to loosen/get play to squeeze the belt on...it's recommend on this 4.0 setup to start the belt on the crank pulley. On the tube ...it's already on there...start and see if it leaks....I put gasket adhesive on the threads of mine.
Joined Sep 7, 2015
·
1 Posts
Any extended life antifreeze will last well over 100k..we sell Shell Rotella ext life 50/50 mixed and your not supposed to touch it until 300k in big rigs. At 300k you put a bottle of extender in it and keep on running.